have questions?
No Duties or Brokerage
We know our products
Always the correct part
Free shipping over $499
The IE FDS front-mount intercooler kit (FMIC) increases horsepower and eliminates heat soak. Get the most out of your tuned 2018+ Audi 3.0T or 2.0T engine by installing the IE FDS intercooler system. The intercooler kit is complete and drop-in. Installation is possible in an afternoon using a standard toolset.
The IE FDS (Flow Distribution System) has proven to distribute charge air uniformly across the inlet end of the core. In contrast to other intercoolers on the market, which rely on natural airflow across the core, our FDS technology uses precisely shaped and placed fins cast into the inlet plenum to fully take advantage of the large core volume effectively using the entire core. As a result, the IE FDS intercooler has been proven to reduce IAT (intake air temperatures) more so than competing intercoolers, thus offering the largest power gains possible.
Increasing the horsepower of your B9 is a simple task with several tunes and upgraded turbos available. However, it is important to keep in mind that increasing horsepower will result in heat soak of the stock intercooler and parasitic power loss. The IE front-mount intercooler system was designed to replace the factory unit directly while utilizing a much larger core and our proven FDS (Flow Distribution System) to effectively utilize that larger core. These features allow for much higher cooling efficiency than the factory system, thus reducing intake air temperatures and safely increasing horsepower output. The IE FDS intercooler is also a direct fit, requiring no cutting, modification, or time-wasting hassle during installation. Read below for more in-depth information on each intercooler feature.
Heat soak occurs when the heat generated exceeds the cooling capacity of the intercooler. The most common symptom is the noticeable loss of power after long-term acceleration, or several back-to-back power pulls. By greatly increasing the core size and useable area of the core with FDS technology, we have eliminated the heat soak, keeping the intake air temperatures consistently lower than OEM and competitor intercoolers. (See dyno chart in power charts tab)
Unlike other intercoolers put together to fit on the car and offer a larger core, the IE FDS intercooler line receives special treatment from start to finish. Our engineering department uses Computational Fluid Dynamics (CFD) software to optimize the end tanks and FDS system for minimum pressure drop and maximum flow and cooling.
Along with lower intake air temperatures, the large core within the IE intercooler also decreases pressure drop compared to the factory unit. Simply put, pressure drop is the amount of pressure that is lost as air travels through the intercooler. As airflow boost pressure is raised, pressure drop typically begins to climb. Using a larger core that flows much more freely than the factory core, the pressure drop is reduced, decreasing the need for the turbocharger to work harder to produce the required boost levels. This allows the turbocharger to deliver more usable boost pressure to the engine. (See dyno chart in power charts tab)
Not only does it offer the highest cooling efficiency on the market, but the IE FDS intercooler also offers perfect OEM replacement with absolutely minimal modification. It has CNC machined mount points, and every IE intercooler allows you to reuse the factory mounting points and installs as if it were a factory piece. You will also find that the IE intercooler receives the same attention to detail and quality as every other IE product, with cast and machined end tanks, precise TIG welding, and a dense bar and plate core. Every intercooler is tested on our in-house intercooler testing station before shipping, ensuring that it is ready to install.
The kit comes complete with one FDS intercooler and all hardware needed for installation.
Install for the IE B9 FDS Intercooler will require a standard toolset, a couple of torx bits, and some technical expertise. We recommend reviewing our install guide and install an overview video before attempting the install. The installation guide can be found HERE.
The IE Audi B9 FDS Intercooler increases horsepower & torque by decreasing IAT (intake air temperature) and reducing knock. This makes your car much more predictable and consistent because it will not rapidly soak like the OE Intercooler.
Typically upgrading to a larger intercooler core results in added pressure drop, resulting in power loss. IE's FDS design eliminates this problem and delivers more boost to the engine by minimizing pressure drop across the intercooler. On the B9 platform, our FDS Intercooler reduces Pressure drop from 1PSI to .3- a drop of approximately 70% at Stage 1 power levels!
Our unique IE FDS Intercooler design for the Audi B9 platform consistently results in an IAT drop of approximately 20C-30C average at the end of open throttle pulls compared to the factory intercooler.
The highly engineered FDS design unique to IE intercoolers uses a carefully shaped fin system located inside the intercooler end tank to force the intake air path. This ensures charge air utilizes the full intercooler core more effectively than conventional intercoolers resulting in less pressure drop, lower IAT temps, and more power resulting in the most efficient intercooler design on the market.
Notice: Intercooler is not compatible with late-model year vehicles that are equipped with active grille shutters. Please verify if your facelift B9.5 car has this feature before ordering.
At what point will I need the IE FDS intercooler for my car?
With extensive testing, we have found that all B9 chassis vehicles have very poor factory intercoolers and can benefit greatly from our intercooler upgrade. Most beneficial on vehicles equipped with stage 1 software or higher, it is necessary to upgrade with a big turbo setup.
What all is included with the IE FDS intercooler?
The intercooler kit includes the direct-fit core, install brackets, necessary bolts and washers, and an installation manual.
Are there any modifications required to install the intercooler?
No! The IE FDS intercooler is a direct replacement for the applications listed above. There is no trimming, cutting, or modification needed for installation.
Do I need to purchase anything else to install the IE FDS intercooler?
This intercooler includes all necessary hardware and parts for installation.
What kind of power increase will I see with the IE FDS intercooler?
The power increase is dependent on the tune or turbo setup and the boost levels that you are running. Tuned ECUs and larger turbo setups run higher boost pressure, higher boost yields larger gains with the IE FDS intercooler.
How much horsepower will the intercooler support?
We have tested the IE FDS intercooler to over 600hp successfully with room to grow. Supported power is in the 650-700hp range but will ultimately depend on the turbo setup and operating conditions.
When Will This Ship?
Please confirm availability on the products page...
In Stock This product will ship within one business day. Available for local pickup in Québec, Canada.
Direct Ship Subject to supplier' stock. Orders typically ship within 2 to 3 business days.
Regularly Stocked Product This product is in stock from our supplier. Orders typically ship within 6 to 12 business days.
Warehouse Transfer Subject to supplier' stock. Orders typically ship within 6 to 12 business days.
On Order This item is on its way to our warehouse.
Back Order This part is back-ordered therefore shipping time will vary.
No Longer Available The manufacturer no longer sells this item, and we can no longer get it from any of our suppliers.
*The processing time and availability are subject to the suppliers’ stock.
Need it faster?
Feel free to reach out before placing your order if you need it faster or require further assistance! 😊
Free Shipping
All orders of $499 or more being shipped within Canada qualify for free standard shipping. Additionally, orders less than $499 qualify for an exclusive low shipping rate.
You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).
If you need to return an item, simply login to your account, view the order using the "Complete Orders" link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.
In-Stock Products
In Stock
Items marked as "In Stock" are physically in our facility, so they're ready to ship when the order is placed. If all items in your order are "In Stock", then your order typically ships within one business day.
Other Availability Modes
We use several availability modes to most accurately identify when products will leave their home facility:
Direct Ship This product is available and will be sourced from one of our suppliers. It may take up to three business days before it ships.
Warehouse Transfer We receive the item, then we ship it to remain on time with the guaranteed delivery range chosen at checkout. It typically takes between 6 and 12 business days before it ships.
Discontinued - No longer available This product has been discontinued by the manufacturer and is no longer available.
We update our catalog daily to provide the most accurate fitment information possible. When shopping for parts, please use the “select your vehicle” car selector on the home page. Once you've selected your car, you can filter parts specific to it.
Additionally, on each product page, we have a tab for fitment information. By clicking on "Fitment", you can scroll and verify the part you are about to add to your cart indeed fits.
Furthermore, if you have a vehicle added to our vehicle selector and you are viewing a product page, you'll see fitment information below the "add to cart" button. If an item fits your car it will display "This Part Fits Your: Selected Vehicule". If an item does not fit your vehicle a message will display "This Part Does Not Fit".
A “Core Charge” is similar to the deposit you might pay for a can or bottle of soda. In many states, to promote recycling, you are charged a deposit when you purchase a can of soda and you receive your deposit back when you return the empty can. Many automotive parts have Core Charges that work the same way as a soda can deposit. The most common car parts that include a core charge are alternators, calipers, steering racks, and fuel injectors.
"MAP" pricing, or Minimum Advertised Pricing, means that the vendor set a minimum retail price that we're not allowed to violate. MAP items cannot be discounted because the decrease in price would violate that threshold.
Integrated Engineering
The IE FDS front-mount intercooler kit (FMIC) increases horsepower and eliminates heat soak. Get the most out of your tuned 2018+ Audi 3.0T or 2.0T engine by installing the IE FDS intercooler system...
Integrated Engineering
034Motorsport
Replace your stock rubber brake hoses with these performance-minded stainless steel braided lines from 034Motorsport! Unlike the stock rubber hose, this stainless steel braided hose will not bulge or...
Integrated Engineering
